Sliding glass doors involve tracks and often are elevated off the floor making traversing with a wheelchair a challenge. Power wheelchairs with larger casters or mobility scooters don’t usually have trouble with the tracks for sliding glass doors because of the larger wheels that roll over obstacles easier.
Wheelchair and scooter batteries are designed to last for years with proper care and maintenance. They are the most common cause of service calls and can cause all kinds of weird symptoms if not working properly.
I’ve recently been helping a lady work out a battery issue with her scooter and felt that the information I’ve been giving her might be of benefit to the readers of MobilityBasics.ca
I was contacted last week from a lady wanting information about the width of a doorway that is needed for a wheelchair to pass through easily. Although this seems like it should have a simple answer, it doesn’t.
After writing a rather long and complicated response by email, I thought it should be a topic that I should go into with more depth on the website.
So, I’ve added a page in the Articles section of the Mobilitybasics.ca website about wheelchair and doorway widths for those who are interested.
As you may or may not know the Mobilitybasics.ca website is supported by our advertisers. These companies make it possible for our visitors to get all kinds of information relevant to disabilities and home medical equipment for free and without any requirement to sign up for newsletters or provide any personal information.
So, when one of our advertisers has something they want to promote I’m happy to oblige and help them any way I can. This helps them, me and our visitors.
I’ve added a page to the wheelchair section of the site today with information on Rowheels replacement wheelchair wheels. I came across these wheels when researching different types of alternative drive systems for manual wheelchairs and thought this was something many people may be interested in.
These wheels provide benefits to the user in terms of more efficient wheeling, improved posture, reduced shoulder injury, strengthened back muscles and improved range of motion.
These wheels, as the name suggests, propel the wheelchair when the user turns the hand rims backwards. Like a rowing a rowboat, the user pulls backwards to propel the wheelchair forward. The difference is, of course, the wheelchair user will be facing the direction they are going.
There is a lot of data and studies to support the theory of pulling back to propel forward and when I think about how one propels a wheelchair it actually starts to make sense.
While pulling backward to propel forward may have many benefits, I’m not sure that these are wheels that a long term wheelchair user could easily change over to. I’m sure the learning curve experienced by user will vary greatly and new wheelchair users will probably have less issues with this departure from normal wheel chair propulsion.
Okay, this is a little bit different from the normal stuff I post about but thought my visitors might be interested in it.
There is an article in the Toronto Star today about a little girl who uses a home made wheelchair built by her parents. The young girl is paralyzed below the arms by a tumor on her spine and there was no expectation she’d be able to even pull herself around on the floor for two or three years. Apparently it didn’t take long before she figured out that by pushing and pulling on the wheels she could move around their house independently.
Her mom went online looking for wheelchairs for toddlers and found a design that they could make at home for about $100.00 using an off the shelf toddler seat, a cutting board, a couple of small bike wheels and a couple of casters.
I’ve recently been looking at propulsion aids for people who have limitations that make propelling a wheelchair difficult. The last few wheelchair devices I added to the site were to make propulsion easier by using motors. Today I’ve added a page on the Neater Uni-Chair.
The Neater Uni-Chair is designed to provide people who only have the use of one foot and one hand independent mobility in a manual wheelchair. The Uni-Chair uses a single handrim that propels both wheels through a specialized differential and a movable footplate that allows the user to steer the wheelchair with their foot.
This chair is manufactured in the UK but is available in North America through their US distributer.
I’ve added a new product page to the website’s wheelchair section on the Xtender power assist wheels for manual Quickie wheelchairs. The Xtenders are options for Quickie wheelchairs only and can be added to compatible models at the time of purchase or as an add-on later.
The Xtenders are similar in theory to the Alber e-Motion wheels I added yesterday but have some specific differences. For one, they only are compatible with select Quickie Wheelchairs. Two, they are available in two models depending on the needs of the user. Three, they can be ordered with either Lithium or Nickel batteries. Four, the wheels actually communicate with each other to provide controlled tracking.
I’ve just added a new product page to the Mobility Basics website about the power add on wheels from Invacare. These wheels are battery driven and can be added to many different makes and models of wheelchairs the make propelling the chair easier for the user.
The wheels are operated by pushing on the handrims and can greatly increase the speed of the chair and the power of the user. The combined improvement in propelling the wheelchair leads to more independent use and much reduced fatigue.
The e-Motion wheels can be pushed as regular wheels are pushed and activated when needed for enhanced propulsion or kept activated all the time for constant assistance.